Auto Electrical
LED lighting installation near you
LED lighting installation for interior ambient strips, cargo and bed lights, rock lights and underglow, wired to fused, switched circuits.
- Time at the shop
- 2 h
- about
- Mobile service
- Available
- at your address
- Shops in Canada
- 1
- doing this work
- Your price
- You set it
- shops bid on it
You set the budget
Shops near you send their bids
1 shop in Canada does this
Auto Electrical
What an LED lighting installation is
LED lighting installation adds lights the factory did not fit: footwell and door-panel strips, ambient dash lighting, brighter dome and map lights, cargo and bed lights on a van or pickup, rock lights and underglow. LEDs draw little current and last for years, but the wiring is what separates a clean job from one that flickers, drains the battery or shorts in the first wet winter.
The installer plans where each strip or pod goes and how it will be switched, then takes trim panels off, mounts the lights and routes the wiring out of sight. Power comes through a fuse tap or relay from a circuit that switches with the ignition or door, grounds go to bare metal, and outdoor connections are soldered and sealed against water and road salt. A dimmer or app controller is paired at the end.
- For cars, EVs, vans and trucks
- Takes about 2 h
- Can be done at your address
What does an LED lighting installation cost?
It depends on your vehicle and the shop. Post a job with your budget and compare the bids shops near you send.
Get bids
Name your budget. Shops near you bid.
1 shop across Canada does LED lighting installation.
What to expect
LED lighting installation, step by step
What the job normally covers, what to mention in your request, and the signs that it is time. Every shop says what its bid includes.
The job
What’s included
- Layout agreed with you: which zones, colours and brightness, and where each switch or controller will sit
- Interior trim, sill plates or panels removed with proper clip tools and refitted without rattles
- Power taken through a fuse tap or relay, never spliced into a thin factory wire
- Strips and pods mounted with clips, brackets or adhesive, with wiring hidden so nothing dangles or rubs
- Grounds bolted to bare metal, and outdoor connections soldered and sealed with heat-shrink
- Circuit wired to switch off with the ignition or door, so the lights cannot drain the battery
- Dimmer, switch or phone controller fitted and paired, with a quick demonstration
- All new and existing lights tested, with no warning lights or bulb-out messages left on the dash
Checklist
Before you post
- 01Tell the shop where you want light and what for: ambience, work light, off-road use or show
- 02Find out if the price covers the lights and controller or only the installation
- 03Ask how the lights are fused and switched; a fused feed that turns off with the ignition protects the battery
- 04Ask which colours and positions suit road use; flashing lights and some colours facing other drivers are restricted
- 05Leasing? Ask for plug-in fuse taps and no cut wires, so it can come out cleanly at the end of the lease
- 06Ask for a written warranty covering the wiring and mounting, not only the LED hardware
Signs
When you need it
- The cabin is dark at night and you want footwell, door or dash lighting
- You work from a pickup or van and need light in the bed, toolbox or cargo area after dark
- You want rock lights, underglow or exterior accent lighting the vehicle did not come with
- A stick-on kit runs from a cable to the 12 V socket and you want it wired in neatly
- An earlier DIY kit flickers, has died or drains the battery
Sound familiar?Tell shops near you what you need and what you want to spend.
Get bidsHow it works
Get an LED lighting installation done in four steps
You set the budget and choose the shop. Posting is free, and you pay the shop you hire once the work is 100% done.
- 01
Post your job
Choose the service, describe the job and your vehicle, and set your budget. It takes two minutes and costs nothing.
- 02
Shops compete
Nearby shops that do the work see your request and send their best offer: price, when they can start, what is included.
- 03
Accept the best offer
Compare bids, ratings and distance, then hire one shop. The others are told, politely.
- 04
Talk and get it done
Your conversation with the shop opens right away to agree on the day. You pay only after the job is complete.
Keep exploring
Related services
Headlight & bulb replacement
Burnt-out headlight, brake light, turn signal and taillight bulbs replaced with the correct type, then every lamp tested and the beam pattern checked.
Mechanical Repair
Light bar installation
LED light bar installation: bars, pods and driving lights mounted and wired through a relay, fuse and switch so they run only when you turn them on.
Auto electrical repair
Auto electrical repair for blown fuses, dead circuits, warning lights and overnight battery drain, with the faulty wire, relay or connection traced and fixed.
Car stereo installation
Car stereo installation with the right dash kit and harness, keeping steering wheel controls and adding Bluetooth, Apple CarPlay or Android Auto.
Questions
Questions about LED lighting installation
General answers for drivers in Canada. The shop you hire confirms the details for your vehicle.
Can LED strips drain my battery?
Only if they are wired to a circuit that stays live. LEDs draw very little, but a strip connected straight to the battery keeps drawing after you park and can drain a battery over a few days. An installer runs the feed through a fuse and from a circuit that shuts off with the ignition or door, and puts a relay in front of anything larger than a few strips.
Can I use underglow or coloured LEDs while driving in Canada?
Only within limits, because road rules restrict flashing lights and certain colours facing other drivers. Lights that dazzle or distract are a safety problem whatever the colour, and many owners keep show lighting for when the vehicle is parked. Ask the installer how yours will be set up, put a separate switch on it, and if you are unsure check with your province’s transportation ministry.
Can I install an LED strip kit myself?
Stick-on kits that plug into the 12 V socket are easy to fit, though the cable stays visible and the strip goes off with the ignition. Hardwiring is where mistakes happen: a tap on the wrong fuse can interfere with airbag or engine computer circuits, poor grounds cause flicker, and an unfused wire is a fire risk. If you are unsure which fuses are safe to tap, pay for the wiring.
Why do my LED lights flicker or trigger a bulb-out warning?
Vehicles that watch their bulbs for burnout read the tiny current draw of an LED as a failed lamp, which shows as a dash warning or a fast-blinking turn signal. Flicker usually comes from a poor ground, a shared circuit that pulses or a cheap driver. Fixes are LED bulbs built for vehicles that monitor their lamps, load resistors, or a proper switched feed for new strips.
How long does LED lighting installation take?
Changing interior bulbs takes under an hour. Footwell or ambient strips take about one to two hours, cargo or bed lighting two to three, and underglow or rock lights half a day, because they mean lifting the vehicle, mounting pods and running sealed wiring along the frame. Tight trim or fibre-optic ambient systems take longer.
Something else to ask? Once you hire a shop, you talk to it directly in your request’s conversation.
Ready when you areTell shops near you what you need and what you want to spend.
Get bidsFor auto electrical shops
Sign up as a business
Auto electrical shops across Canada: drivers post their Auto Electrical requests here. Publish your weekly flyer, open the appointment windows you can take and bid on the jobs near you. Free while we launch, no commission.